How-To/DIY: Install Si-VTEC foglights & Center Console Switch

In the United States, the Acura Integra did not receive fog lights until 1998 when the Integra Type R was released. But what about the gap in 1994 to 1997? The so called “bug-eyed” front end did have fog lights but was only released in Japan. These fog lights came in OEM Stanley light housing and came in two colors: clear and yellow. In Japan, the Si-VTEC fog lights were only in production when the “bug-eyed” front end was in production which was from 1993 to 1995. So unless you were into the JDM scene then, the Si-VTEC fog lights were a rare item to get your hands on a set, especially with OEM wiring harness, center console switch & hardware, in the United States.

Here you can see the used Si-VTEC foglights & Center Console Switch I picked up from a friend who was building up an DB8. It came with the OEM hardware, brackets, plastic bezels and center console button.

1 SiVTEC Foglights & Supplies Needed (2)1 SiVTEC Foglights & Supplies Needed (3)

Here is a Wiring Diagram I drew up to keep my work in proper order and to lessen any kind of confusion when it comes to the wiring of this process. Keep this in mind or refer back to this whenever you are feeling confused about this How-To/DIY project.

1 SiVTEC Foglights & Supplies Needed (4)

Keep in mind, I am an Amazon affiliate and some of the links below are affiliate links, which means that if you choose to make a purchase, I will earn a commission. Please understand I have had experience with this product and/or only recommend what I believe will be helpful and useful, not because of the small commission I make if you decide to buy something. Please be wise and do not spend money unless you feel you need them or that it will help you achieve your goals.

Below are the supply and parts needed for this How-To/DIY tutorial and my personal recommendations. Each one has been carefully selected to make this How-To/DIY tutorial easy for you to achieve with a quality finish:

 

1 SiVTEC Foglights & Supplies Needed (1)

Before I did this How-To/DIY on Installing OEM Honda Integra Si-VTEC fog lights, I made sure I understood the wiring behind it to avoid any confusion. Since I did not have the OEM wiring harness for this installation of fog lights, I had to come up with my own. I used a 5-pin relay, crimped female disconnects and primary wire to setup everything to plug into the existing plugs and ports.

Here is the link to learning to Soldering Wires.

I provided the link because I had to create a harness from my own resources. With your primary wire, cut a length that will reach from the center console to the under-dash. You’ll have to strip about half an inch of insulation from the wire to solder to the center console button wires. Now crimp a female quick disconnect to each wire.

Here you can see my own DIY fog light harness:

1 SiVTEC Foglights & Supplies Needed (5)a1 SiVTEC Foglights & Supplies Needed (6)aa

Now that you have the wiring harness all set up to be plug and play, let’s dive deep in removing everything to install the fog lights and have it wired correctly to work on our command.

Step 1:

  • Remove the bumper

  • Remove 2 x screws on the side bottom

  • Remove 2 x screws on the turn signal lights

  • Twist and pull out the two plugs from the turn signal lights

  • Remove 9 x screws from the front bumper stiffener

  • Remove 2 x 10mm bolts from each side plates

  • Remove 2 x 10mm bolts on the bottom and/or Splashguard

  • On each side, pop the side plate clips off and proceed to pull the bumper outward and off

2 Remove Integra Front Bumper (5)a2 Remove Integra Front Bumper (3)a

 

Step 2:

  • Cut out the polyurethane on the front bumper grill

  • Make sure to leave the mounting hole areas intact

3 Install SiVTEC foglights onto Integra Bumper Grill (0)3 Install SiVTEC foglights onto Integra Bumper Grill (1)3 Install SiVTEC foglights onto Integra Bumper Grill (2)

 

Step 3:

  • Mount the Si-VTEC fog lights

  • Mount fog light bezels

  • NOTE: The front bumper has “notches” for the fog light bracket to snatch onto to help keep alignment.

3 Install SiVTEC foglights onto Integra Bumper Grill (3)a3 Install SiVTEC foglights onto Integra Bumper Grill (8)a

 

Step 4:

  • Solder and extend the wires on the fog lights

  • For the right passenger side, I extended the ground cable

  • For the left driver side, I extended both power and ground cables

3 Install SiVTEC foglights onto Integra Bumper Grill (13)a

 

Step 5:

  • Mount the fog light ground cables

  • Plug the fog light wire to existing fog light plug

3 Install SiVTEC foglights onto Integra Bumper Grill (16a)3 Install SiVTEC foglights onto Integra Bumper Grill (17)a

 

Step 6:

  • Reinstall the front bumper

 

Step 7:

  • Remove the Center Console

  • Remove the access cap with a flat tip screwdriver & remove 2 x screws

  • Remove the 2 x screws from the rear console

  • NOTE: To remove the screws, slide the front seat forward

  • Remove the rear console

  • NOTE: Lift up the parking brake lever

  • Detach the hooks by lifting the front of the rear console and sliding it rearward

  • Remove the ashtray

  • Remove 2 x screws to remove the front console panel and disconnect the connector

  • Remove 4 x screws from the front console

  • Depending if you’re A/T or M/T:

  • Wrap the shift lever and A/T gear position indicator panel with a shop towel to prevent damage

    OR

  • Remove Shift Lever Knob

  • Remove the front console by lifting the back upward, twisting to one side and then upward after it clears the parking brake lever

4 Remove Center Console (1)a

 

Step 8:

  • Feed the center console switch connector thru the carpet to rear console

  • Pop out one of the plastic pieces and snap the Fog light switch into place

5 Center Console Foglight Switch (4)a




Step 9:

  • Plug the connector to the switch

  • Reinstall the center console

5 Center Console Foglight Switch (3)

Step 10:

  • Mount the relay under the dash

  • Plug each connector to the correct positions:

  • Relay 87 – To stock Fog light wire under-dash

  • Relay 86 – 12V Foglight Switch Pin 3

  • Relay 85 – Ground

  • Relay 30 – To 30AMP Inline Fuse to 12V Constant under-dash

  • Foglight Switch Pin 1 – To 12V Accessory under-dash

  • Foglight Swtich Pin 6 – Ground

6 Foglight Underdash Wiring (1)a

Step 11:

  • Test and turn on fog lights

NOTE: If it does not turn on,

  • Check your connections are in the right positions

  • Check if the inline fuse is good or blown

  • Retry different ports on the under-dash fusebox and remember:

  • Port 1, 2 – Constant 12V

  • Port 3, 5 – Accessory 12V

  • Port 4 – Parking Lights

7 SiVTEC Foglight (1)7 SiVTEC Foglight (2)

 

Leave a Reply